Optifit Instructions. LOFT settings are. To adjust the Callaway Big Bertha Alpha Driver How to Adjust Loft and Lie Angle on Callaway X2 Hot Driver. Un Cadavere Di Troppo Pdf Merge on this page.

You want precise control so you’ve chosen an adjustable driver. And the adjustable driver of your choice is the Callaway X-Hot. Reviews about this club will tell you about how the club performs. But they rarely address using the adjustable settings. Have no fear. Your new Callaway driver won’t languish in the closet. We’ll tell you how to set the proper face angle for your swing.

Soon you’ll be able to tweak your driver’s hosel so and get the most out of every stroke. Let’s walk through the settings available on your new driver.

Neutral The letter “N” indiciates a neutral or square face angle. Sportbike Suspension Tuning Ebook3000. Position it between the two lines on the adjustable hosel of your new Callaway driver. Neutral or square faces are exactly what you’d imagine.

They have no angle whatsoever when they’re held at a perfect 90 degree angle to the line of flight. When you strike your ball, it’ll fly exactly where you’re pointing. That is, if your swing is perfect. Neutral face settings are perfect for certain conditions.

Use this setting when you’re shooting straight down the fairway, the wind is calm and there aren’t any objects or hazards between you and your target. Open The open setting, indicated on the Callaway X-Hot’s hosel with an “O”, opens the clubface 2.5 degrees and lowers the loft of the club by about 1 degree. The opening of the clubface creates a fade or slice shot. That is, a shot that curves to the right for a right-handed player; you can use it to correct shots that tend to fly too far to the left.

But with this correction, the Callaway X-Hot punishes you by making it more difficult to get your ball in the air. You need to be making an extra effort to swing your driver well or buy a higher lofted club if you plan to use the “O” setting. Closed Closing the face angle by selecting the “C” setting on your hosel closes the face down 1.5 degrees and increases your loft by a degree.

Closed faces create hook and draw shots, which curve to the left as they travel away from a right-handed golfer. Again, use this face angle to correct or get around a hazard or obstacle. The increased loft angle will help you get your ball up off the ground a little easier. Don’t worry if your new Callaway driver isn’t for you.

We’re happy to take it in trade toward a different club. You could trade up to a more adjustable Callaway or into something a lot more traditional. Just know that we’ve got the perfect driver for your game.

Callaway Club Specialist, Ross Stewart shows you how to adjust loft and lie angle on the new X2 Hot Driver. Here is how you can adjust loft and lie angle on your X2 Hot Driver: Loft and Lie Adjustability Instructions We recommend that you make adjustments in the order below: 1. LOFT options • stated loft (S) • stated plus one degree (+1) • stated plus two degrees (+2) • stated minus one degree (-1) The loft lets you adjust launch angle and backspin to influence trajectory. The club comes set in the stated “S” position.

To change the loft, loosen the screw at the bottom of the shaft and rotate both cogs until the loft setting you want is aligned with the white hash mark on the shaft and the white hash mark on the driver hosel assembly. Tighten the screw until you hear a click. Note: Your desired loft may appear on the upper or lower cog, depending on loft and lie angle combination. LIE options • Neutral (N) • Draw (D) Once the loft has been determined, hold that cog in place while you rotate the other cog between Draw “D” and Neutral “N”. This will change the lie angle and influence the starting direction of your shots. If you want to minimize a slice or enhance a draw, rotate the lie cog to the Draw “D” position, which will make the lie angle more upright. If you want to work the ball both ways, for either a fade or a draw, rotate the cog to the “N” position.

Remember that this designation could appear on the upper or lower cog, and make sure the desired setting is aligned with the white hash mark on the shaft. Always tighten the screw until you hear a click. The figure below illustrates the do’s and don’ts for adjusting your hosel settings: Here’s an example: To adjust your 10.5° clubhead to 11.5 degrees of Loft and a Neutral position: • Find “ +1 ” on one of the two cogs and line it up with the hash marks on the shaft and clubhead hosel. • On the other cog, find the “N” setting and align it with the two hash marks. • Tighten screw until you hear a click.